Just How To Install A Bathtub (For Newbies).
Just How To Install A Bathtub (For Newbies).
Blog Article
This post listed below in relation to Installing A Bathtub is highly entertaining. You should see for yourself.
Setting up a bath tub isn't specifically brain surgery, but it does need strong plumbing, carpentry, as well as sometimes, tiling abilities. Replacing an old tub with a brand-new one is additionally a reasonably challenging task. If the old tub is conveniently available, the job can move immediately; if you have to open up a wall surface to eliminate the old bathtub as well as place the new tub, the job is much harder. In either instance, the project is within a house handyman's abilities, although you will require an assistant to move out the old bathtub and set in the brand-new one. Make sure you have certified yourself for the task and also are comfortable trying it. Instead of working with a service provider to take over a halfway-completed task, it is much better to think about using one before you begin. Opportunities are you may need a specialist plumber to make tube connections.
This short article will certainly help you set up a brand-new bath tub in your restroom if you have actually currently acquired a new tub as well as do not require to transform the arrangement of your previous water system pipelines.
Your tools and material list ought to make up the following:
Planning for the Installation
First of all, the supporting frame supplied with the bath ought to be fitted (if required) according to the manufacturer's instructions. Next, fit the taps or mixer to the bath tub. When suitable the faucet block, it is very important to make sure that if the faucet features a plastic washing machine, it is fitted in between the bath and the faucets. On a plastic bathroom, it is additionally practical to fit a supporting plate under the faucets system to prevent strain on the bathtub.
Fit the flexible tap adapters to the bottom of both faucets using 2 nuts as well as olives (in some cases supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the electrical outlet with the hole in the bath. Use the nut provided by the supplier to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the adaptable overflow pipeline to the overflow outlet. After that, screw the pipeline to the overflow face which need to be fitted inside the bath. Make sure you make use of every one of the supplied washers.
Attach the catch to the bottom of the waste outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Link the bottom of the overflow tube in a comparable manner.The bath should currently be ready to be suited its last setting.
Removing Old Taps
If you require to change old taps with brand-new ones as a part of your setup, then the first thing you need to do is detach the supply of water. After doing so, turn on the faucets to drain any water continuing to be in the system. The process of getting rid of the existing faucets can be quite bothersome because of the limited accessibility that is commonly the case.
Make use of a basin wrench (crowsfoot spanner) or a tap device to undo the nut that attaches the supply pipes to the faucets. Have a fabric all set for the staying water that will originate from the pipes. As soon as the supply pipes have actually been removed, make use of the exact same device to loosen the nut that holds the taps onto the bath/basin. You will certainly need to quit the single faucets from transforming during this procedure. Once the taps have actually been eliminated, the holes in the bath/basin will have to be cleaned of any type of old sealing compound.
Prior to carrying on to fit the brand-new taps, contrast the pipe links on the old taps to the brand-new taps. If the old faucets are longer than the new faucets, then a shank adapter is needed for the new taps to fit.
Mounting the Bathtub
Utilizing both wooden boards under its feet, position the tub in the called for setting. The wood boards are valuable in equally spreading the weight of the tub over the area of the boards rather than focusing all the weight onto 4 little points.
The following objective is to make sure that the bathtub is leveled all round. This can be attained by checking the level and also adjusting the feet on the bath tub until the level reads level.
To set up faucets, fit the bottom of the outermost flexible tap adapter to the appropriate supply pipeline by making a compression sign up with; after that do the same for the other tap.
Activate the supply of water as well as examine all joints and new pipework for leakages and also tighten them if essential. Fill the bathtub and additionally examine the overflow electrical outlet and the typical electrical outlet for leakages.
Finally, take care of the bathroom paneling as defined in the supplier's instruction manual. Tiling and also sealing around the bathtub must wait till the bath tub has been utilized a minimum of when as this will settle it into its final placement.
Fitting New Touches
If the tails of the brand-new taps are plastic, then you will require a plastic port to stop damages to the thread. One end of the adapter fits on the plastic tail of the faucet and also the various other end provides a connection to the existing supply pipes.
If you need to fit a monobloc, then you will need decreasing couplers, which links the 10mm pipeline of the monobloc to the standard 15mm supply pipe.
Next, place the faucet in the placing opening in the bath/basin making certain that the washing machines remain in area in between the faucet and also the sink. Protect the tap in place with the producer provided backnut. As soon as the faucet is firmly in position, the supply pipelines can be attached to the tails of the faucets. The faucets can either be linked by using corrugated copper piping or with regular faucet adapters. The previous kind must be linked to the faucet ends first, tightening up only by hand. The supply pipelines can later on be attached to the other end. Tighten both ends with a spanner after both ends have been connected.
Tiling Around the Bath tub
In the location where the bathroom satisfies the ceramic tile, it is needed to seal the joins with a silicone rubber caulking. This is important as the fitting can relocate enough to crack an inflexible seal, creating the water to permeate the wall between the bath and also the tiling, bring about issues with dampness and also feasible leaks to the ceiling below.
You can pick from a range of coloured sealants to blend in your components and installations. They are marketed in tubes as well as cartridges, and can securing gaps up to a width of 3mm (1/8 inch). If you have a bigger void to fill up, you can fill it with spins of drenched newspaper or soft rope. Remember to constantly fill up the bath tub with water before securing, to enable the movement experienced when the bathtub is in use. The sealer can break fairly early if you do not think about this movement before sealing.
Conversely, ceramic coving or quadrant ceramic tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are also conveniently offered on the market. It is a good idea to fit the floor tiles utilizing water-resistant or waterproof glue as well as cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
As an enthusiastic reader about A Step-by-Step Guide to Installing a Bathtub, I was thinking sharing that article was a great idea. Loved our blog entry? Please share it. Help another person check it out. I am grateful for your time. Don't forget to come by our website back soon.
Click On This Link Report this page